Planar Computer Monitor CM174SXAD User Manual

VitalScreen 17.4" Display  
VS17.4SXAD / CM17.4SXAD  
OPERATIONS MANUAL  
 
iii  
Regulatory Compliance  
VitalScreen CSR  
This display has been tested and found to comply with IEC/EN 60601-1  
and IEC/EN 60601-1-2 standards, and is certified to meet medical  
standard C22.2 No. 601.1-M1990 (C US Mark).  
The medical display, in addition to meeting medical requirements,  
has been tested and found to comply with the limits for Federal  
Communications Commission (FCC) Class B computing devices in  
a typically configured system since many medical offices are located in  
residential areas. It is the system integrators responsibility to test and  
ensure that the entire system complies with applicable electromagnetic  
compatibility (EMC) laws.  
Planar Systems, Inc. has made great efforts to support the medical  
device industry, in particular, medical device manufacturers and medical  
device system integrators. We offer state-of-the-art color displays that are  
compliant with worldwide accepted medical device safety standards, and  
for the European market, CE-marked displays based on compliance with  
counsel directive 93/42/EEC—commonly referred to as the Medical Device  
Directive (MDD). The following summarizes our qualification of these  
displays as it relates to compliance with the MDD.  
The European Medical Device Directive requires that the intended use  
of the device be defined. The intended use of these displays is to display  
alphanumeric, graphic, and image data as inputted from any type of  
medical device.” These displays do not provide a measurement function  
in any way, and it is the device and systems manufacturers responsibility  
to verify its function in the integrated device or system.  
The display was classified as required by the MDD according to Annex IX  
of the directive and the medical device (MEDDEV) guidance available  
at the time of classification. Because the display uses electrical energy  
and has no direct patient connections andby itselfno medical utility,  
the display is classified according to Rule 12 as an MDD Class I device-  
component or accessory. The MDD states that manufacturers of Class I  
medical devices or accessories shall satisfy the requirements in regard  
to design and manufacturing controls, that is, the applicable assessment  
route to be used for CE-marking under the MDD, and it shall carry  
the CE mark according to Annex XII of the directive, with no notified  
body annotation.  
The applicable safety standards for an MDD Class I display are  
IEC/EN 60601-1:1900 along with Amendments 1 and 2. To help the  
medical device designer evaluate the suitability of these displays,  
Planar has also conducted EMC testing to IEC 60601-1-2 as it can  
be applied. The display with its power supply alone does not represent  
a functional medical device. Hence, Planar configured a minimal  
operating system to exercise the display. The resulting data are  
made available to interested parties.  
The data are informative data, not certification data. Certification  
data must be obtained by the device or system integrator according  
to Article 12 of the MDD titled Particular procedure for systems and  
procedure packs.” Paragraph 2 clearly outlines the device or system  
integrators responsibility in this matter.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
iv  
In summary, Planar Systems, Inc. is CE-marking these displays  
under the Medical Device Directive, which establishes compliance to  
the basic medical safety standards. However, EMC compliance can  
only be accomplished in the configured medical device or system and  
is the responsibility of the device or system manufacturer. Planar has  
the necessary documentation such as IEC 60601-1 notified body and  
other third-party test reports and certifications, a risk/hazard analysis,  
an essential requirements checklist, and the Planar International  
Electrotechnical Commission (IEC) declaration of conformity.  
Planar Systems, Inc., located in Beaverton, Oregon, USA, is the  
manufacturer of these displays in the meaning of the directive.  
As required by the MDD in Article 14, Planar Systems, Inc., not  
residing in the European Economic Area (EEA), has a European  
representative, Planar Systems, Inc.Espoo, Finland.  
In the opinion of Planar Systems, Inc. registration required to put this  
device into commerce is the responsibility of the medical device/system  
manufacturer, and Planar supports this requirement by providing a  
European Commission (EC) declaration of conformity. If Planar supplies  
a display to an end user, rather than a device manufacturer, it is the end  
users responsibility to ensure continued compliance with the MDD of  
the system in which the display is integrated.  
For vigilance reporting as required under Article 10 of the MDD,  
Planar Systems, Inc. will provide any information requested by  
competent authority to support any reported incident investigation  
by such an authority.  
European Union Declaration of Conformity for Medical Applications  
A Declaration of Conformity has been filed for this product. For  
additional copies of the Declaration of Conformity document, contact  
Planar Systems, Inc. and request document number 001-0014-05  
Declaration of Conformity.”  
VitalScreen CR  
Manufacturer Declaration  
This certifies that this product is in compliance with the EU Directive  
89/336/EEC, using the EMC standards EN55022 (class B), EN50081-1  
and EN50082-1. This product meets or exceeds EN60950, UL1950, and  
CSA 22.2 No. 950 safety requirements. This product has been tested and  
verified to meet CISPR 22 Class B requirements.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
v
FCC Compliance Statement  
This equipment has been tested and found to comply with the limits for  
a Class B digital device, pursuant to Part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference when the equipment is operated in a residential installation.  
This equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instruction manual,  
may cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment  
off and on, you are encouraged to try to correct the interference by one or  
more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet different from that to which  
the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
To comply with the limits for an FCC Class B computing device,  
always use the shielded signal cord and shielded power cord supplied  
with this unit.  
The Federal Communications Commission warns that changes or  
modifications of the unit not expressly approved by the party responsible  
for compliance could void the users authority to operate the equipment.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
 
vii  
Contents  
About This Manual .............................................................. ix  
Product Information............................................................. x  
1 The VitalScreen 17.4" Display........................................... 1  
VitalScreen CSR ...................................................................... 2  
VitalScreen CR......................................................................... 2  
Distinguishing the Displays ................................................... 2  
Selecting a Workspace............................................................. 3  
Unpacking the Display............................................................ 3  
Identifying the Components ................................................... 4  
2 Installing the Display........................................................... 7  
Safety Precautions ................................................................... 7  
Connecting the AC Power to the Display .............................. 7  
Connecting the Display to the System ................................... 8  
Connecting a Video Device...................................................... 9  
Connecting the Optional Touch Screen ................................. 9  
Mounting the Display.............................................................. 9  
Power Management System ..................................................10  
Landscape-to-Portrait Mechanical Conversion ....................10  
3 The Display Controls..........................................................11  
Using the Onscreen Display ..................................................11  
Onscreen Display Main Menu ...............................................11  
S-Video and Composite Video Settings .................................15  
Onscreen Display Lockout .....................................................16  
Supported CVBS and S-Video Modes....................................16  
Appendix A: Technical Information................................19  
Appendix B: Troubleshooting..........................................20  
Index .......................................................................................21  
Description of Warranty.....................................................23  
Ordering Information..........................................................25  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
 
ix  
About This Manual  
Congratulations on your purchase of the VitalScreendisplay!  
This operations manual will help you set up, use, and maintain  
the VS17.4SXAD or CM17.4SXAD model properly. Retain this  
manual for future reference.  
Read this section carefully to learn how to handle the display safely  
and clean it correctly. It explains the symbols used on the products  
and the conventions used in this manual.  
Chapter 1 provides an overview of the VitalScreen display. It lists  
the contents of the display package and identifies the components of  
the display.  
Chapter 2 explains how to install the display correctly and use  
optional components.  
Chapter 3 explains the menus and function controls built into  
the display.  
Appendix A contains technical information.  
Appendix B focuses on troubleshooting.  
Warranty description and ordering information are provided at  
the back of this manual.  
Conventions  
The VitalScreen display documentation uses these conventions.  
This convention…  
Indicates…  
A warning that can prevent injury to you,  
such as electric shock.  
A note of important information regarding  
a particular topic or procedure.  
A caution that can prevent potential damage  
to hardware or software.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
x | Product Information  
Product Information  
Safety Instructions  
Store the display in its original shipping carton when it is not in  
operation for extended periods of time. Also use the original packing  
materials and carton when shipping the display.  
Do not place the display near a window. Exposing the display to rain,  
water, moisture, or constant direct sunlight can damage it.  
Do not place anything on top of the display-to-computer signal cord.  
Make sure the cord is placed where it will not be stepped on.  
Do not apply excessive pressure to the screen. Excessive pressure  
may cause permanent damage to the display.  
Do not operate the touch screen with sharp objects, such as a scalpel.  
Sharp objects can scratch or damage the touch screen. A damaged  
touch screen may pose a safety hazard.  
Refer all servicing to qualified personnel to maintain your  
warranty. The display and power supply units contain no  
user-serviceable parts.  
Do not cover or obstruct the venting holes on the back of  
the display.  
Store the display in an environment with a temperature  
range from 20 to 65 degrees Celsius (from 4 to 149 degrees  
Fahrenheit). Storing your display outside that temperature  
range could result in permanent damage.  
Replace any cord or cable that is frayed or damaged with  
another of the same type and rating as supplied by Planar.  
(See Ordering Information” at the end of this manual for part  
numbers.) The safety and regulatory listings and certifications  
are based on the cable supplied by Planar.  
Do not expose the display to liquid or drop it. If the case has been  
damaged, the unit may pose a shock or fire hazard. Unplug the unit  
immediately and call customer service for assistance.  
Use only the power adapter that has been tested and approved  
for use with this display product. (See Ordering Informationfor  
part numbers.)  
The power adapter must be plugged into a grounded power outlet.  
Use a cloth dampened with liquid cleaner to clean the power adapter.  
Wipe the outside of the enclosure and cable only. Do not immerse the  
adapter in liquid, or a safety hazard could arise during use.  
Do not use the power adapter near inflammable anesthetics.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
Product Information | xi  
Cleaning Instructions  
The VitalScreen display will continue to operate while being cleaned in  
a fashion normal for a hospital environment. This means cleaning the  
display with a damp, mild soapy cloth.  
The VitalScreen withstands nonabrasive cloths and cleaning solutions  
used in hospital for like equipment. This cleaning typically includes warm  
water and mild detergent for all surfaces or 70 percent isopropyl alcohol  
for the touchscreen surface.  
Possible cleaning solutions  
70 percent isopropyl alcohol  
1.6 percent aqueous ammonia  
Cidex(2.4 percent glutaraldehyde solution)  
Sodium hypochlorite (bleach) 10 percent  
Green soap” United States Pharmacopoeia (USP)  
0.5 percent Chlorhexidine in 70 percent isopropyl alcohol  
Ovation  
Formula 409  
Fantastic  
WexCide  
To clean the screen  
Stand away from the display and spray the cleaning solution onto  
a clean nonabrasive cloth. Without applying excessive pressure, clean  
the screen with the slightly dampened cloth. Dry the screen with  
a clean nonabrasive cloth to remove any residue.  
Do not spray liquid cleaners directly onto the screen.  
Disposal Information  
The VitalScreen display contains cold cathode fluorescent lamps, which  
contain a maximum of 20 milligrams of mercury (5 milligrams per lamp).  
Follow local ordinances or regulations for its disposal.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
xii | Product Information  
Symbol Explanations  
This table explains the symbols appearing on the display or power  
supply adapter.  
This symbol…  
Indicates…  
Proof of conformity to applicable European Economic  
Community Council directives and two harmonized  
standards published in the official journal of the  
European Communities.  
The product has been tested to specific requirements of  
medical or ITE device standards. If this mark appears with  
the indicators “C” and “US,” the product is certified for the  
Canadian and U.S. markets, meeting the applicable  
Canadian and U.S. standards.  
The product has been tested to comply with  
FCC Class B standards.  
More information available in accompanying documents.  
Protective earth ground.  
The product has been tested to comply with Underwriters’  
Laboratories standards.  
Indoor use only.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
The VitalScreen 17.4" Display  
The architecture of the VitalScreenCSR and VitalScreen CR displays  
incorporate an active matrix liquid-crystal display (AMLCD) panel that  
produces a bright, high-contrast image with low radiation emission.  
This technology greatly reduces the radiation-related health concerns  
associated with cathode-ray tube (CRT) monitors.  
Each VitalScreen is a high-resolution color display designed to be  
versatile and easy to use. The display accepts either analog or digital  
video (DVI) input and displays most video standards from 640 x 480  
(VGA standard) to 1280 x 1024 (SXGA standard). The controls located  
on the front panel allow you to easily adjust the display parameters  
using onscreen display (OSD) menus.  
The digital video input is a single-link, transition minimized differential  
signaling (TMDS) digital visual interface (DVI), and is in compliance  
with the Digital Display Working Group (DDWG) DVI standard. This  
interface produces the sharpest display image possible with little need  
for adjustment. The setup is Plug and Play.  
Each display has a built-in mounting platform that conforms to the  
Video Electronics Standards Association (VESA) mounting standard.1  
This configuration allows the display to be mounted in a variety of  
ways, such as on a wall bracket or articulated swing arm. An alternate  
configuration with a desk stand is also available for easy use on flat  
work surfaces.  
Both displays have features making them ideal for hospital applications.  
The housing is an acrylic cover that protects the display from bumps,  
falls, collisions, and even everyday cleaning. In addition, Planar offers  
configuration management to ensure that you receive a consistent and  
predictable product.  
The Planar 17.4" display series, for the first time, consists of these two  
distinct versions: VitalScreen CSR and VitalScreen CR. Both displays  
have been designed for hospital use, but they have several differences.  
1 The VESA Flat Panel Monitor Physical Mounting Interface (FPMPMI)  
Standard defines physical mounting interfaces for flat-panel displays,  
corresponding standards (75 and 100 millimeters) for flat-panel display  
mounting devices, and associated cable, cable connectors, and power supply  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
2 | The VitalScreen 17.4" Display  
VitalScreen CSR  
This display has been designed, tested, and certified for use within  
the patient vicinity. It has lower electric discharge, thus reducing  
the likelihood of electric shock. The display is certified to UL-2601,  
IEC 60601-1, and other representatives of the most stringent electric  
discharge certifications available. In addition, the interface buttons on  
the front panel are sealed by a plastic membrane, allowing simpler and  
safer cleaning. The display also meets the liquid/particle ingress  
certifications, IPX-1.  
VitalScreen CR  
This display has been designed for hospital use outside the patient  
vicinity. It is not certified UL-2601 or IEC 60601-1. In addition, the  
interface buttons are not sealed on the front panel, and the display  
does not meet IPX-1 standards.  
The VitalScreen CR display has been tested and found to comply with  
the limits for a Class B digital device pursuant to Part 15 of FCC rules.  
The interface buttons on the VitalScreen CR display are not sealed  
and can be harmed if exposed to liquids. Use caution when cleaning  
near the front panel.  
Distinguishing the Displays  
Many of the features and benefits that differentiate the VitalScreen CSR  
and VitalScreen CR displays are not visually apparent. The simplest way  
to identify your Planar display is to check the interface buttons on the  
front panel.  
Note these differences for the interface buttons:  
Interface buttons on the front panel of the VitalScreen CSR display  
(left) are sealed by a plastic membrane.  
Interface buttons on the front panel of the VitalScreen CR display  
(right) are not sealed.  
The display on the cover of this manual is a VitalScreen CSR. A plastic  
membrane seals the interface buttons.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
The VitalScreen 17.4" Display | 3  
Selecting a Workspace  
Before unpacking the display, prepare a suitable workspace. You need  
a stable and level surface near a grounded wall outlet in an area that  
is relatively free of glare from sunlight or other sources of bright light.  
The display is cooled by natural convection. For best performance,  
do not block the cooling vents.  
Unpacking the Display  
While unpacking the display, inspect it and other package contents for  
shipping damage that could cause a fire or shock hazard. Immediately  
report any shipping damage to the carrier or transport company, and  
contact customer service for assistance. Keep all packing material in  
case you need to ship, store, or return the display.  
After you unpack the display, make sure you have these items:  
LCD screen  
AC power supply with 1.5-meter (5-foot) cable  
Power cord for the display, which connects from the AC main supply  
to the AC adapter  
3-meter (9-foot) S-Video/Composite Video cable (if you purchased the  
VitalScreen CSR with S-Video and Composite Video support)  
3-meter (9-foot) audio cable (if you purchased the VitalScreen CSR  
with S-Video and Composite Video support)  
75 and 100 millimeter VESA plates (if you purchased  
the VitalScreen CSR without a desk stand)  
2-meter (6-foot) RS-232 serial cable (if you purchased  
the VitalScreen CSR with touchscreen interface)  
2-meter (6-foot) analog video cable (VGA-VGA) with audio  
2-meter (6-foot) digital video cable (DVI-DVI) with audio  
Documentation package including CD, operations manual in English,  
and EU Declaration of Conformity  
If you have questions about what comes with your display, compare the  
part number for the display with the ordering information on page 25.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
4 | The VitalScreen 17.4" Display  
Identifying the Components  
The VitalScreen CSR and VitalScreen CR displays provide easy access to  
all controls and peripheral ports. The following illustrations of the screen  
and the front and back panels identify the display controls and ports.  
17.4" LCD screen  
LCD screen  
A 17.4-inch diagonal AMLCD. The screen supports  
most display standards from 640 x 480 VGA to  
1280 x 1024 SXGA.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
The VitalScreen 17.4" Display | 5  
Front panel  
Power switch /  
Dual function button to control display  
Onscreen display  
power and access the OSD menu. Press  
this button for 2 seconds to turn the display  
ON or OFF. When the display is ON, press  
this button once to access the OSD menu.  
UP and DOWN arrows to navigate the  
OSD menus. When the OSD menu  
displays, press these buttons to select  
a control function.  
Function buttons  
Adjustment buttons  
Controls to adjust the selected setting.  
The MINUS control decreases the selected  
setting. The PLUS control increases the  
selected setting. Press either button to  
select a menu.  
Power ON indicator  
Light-emitting diode (LED) indicator that  
illuminates when the display is ON and  
receiving a proper video signal. The  
LED blinks when the display is in power-  
saving mode.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
6 | The VitalScreen 17.4" Display  
Back panel  
Locking 4-pin power connector  
Connect the low-voltage cable from  
the power adapter to this port.  
USB downstream ports (2)  
USB upstream port (1)  
Audio input jack  
Connect peripherals (e.g., keyboard,  
mouse) to these ports, if desired.2  
Connect the USB cable from the  
computer to this port, if desired.3  
Connect the system audio lineout  
to this port to listen to the system audio  
on the display stereo speakers.4  
Touchscreen (DB-9 serial) port  
Analog (VGA) video input [port 1]  
Connect the system touchscreen cable  
to this port on a resistive touchscreen  
display.  
Connect the system VGA cable from  
the computer VGA output to this port  
for analog mode.  
Digital (DVI) video input [port 2]  
Connect the system DVI cable from  
the computer DVI output to this port  
for digital mode.  
2
Connect USB upstream port to computer to use peripherals.  
For a VitalScreen supporting S-Video and Composite Video, the  
3
S-Video/Composite Video connector replaces the USB ports.  
4
Do not use audio from the display speakers as the exclusive audio source in  
medical applications, especially not as an alarm indicator.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
Installing the Display  
To install the VitalScreen CSR or VitalScreen CR display, first connect  
the power supply unit. Next, connect the video cable. Then choose  
whether to connect optional stereo speakers and touch screen.  
Safety Precautions  
Follow these safety precautions when connecting the display.  
Plug the power adapter into a grounded power outlet.  
Use a surge protector between the AC adapter and the electrical wall  
outlet to prevent sudden current variations from reaching the display.  
Connecting the AC Power to the Display  
1 Plug the receptacle end of the AC power cord into the  
AC power adapter.  
2 Plug the power connector of the adapter into the power port on  
the display. (Locate the locking 4-pin power connector on the  
back panel next to the USB downstream port.)  
3 Insert the power cord into a grounded wall outlet.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
7
 
8 | Installing the Display  
Connecting the Display to the System  
1 Turn off power to the computer, camera, or other output source, and to  
the display.  
2 Connect the appropriate video cable from the display to the video port  
on the output source.  
3 Make sure the video cable connector is securely connected to the video  
port on the output device.  
4 Turn on the display first, then turn on the output device.  
5 Set the output device to a supported resolution, if applicable.  
(See Supported CVBS and S-Video Modes” on page 16.)  
6 If VGA analog is used, select the Auto-Adjust menu on the onscreen  
display, if you are using VGA analog. (See Onscreen Display Main  
Menu” on page 11.) Press the PLUS or MINUS (  
activate it.  
/
) control to  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
Installing the Display | 9  
Connecting a Video Device  
Use the following instructions if you are hooking up a camera, VCR, or  
other S-Video or Composite Video device, and not using the VGA or DVI  
input simultaneously. These instructions apply to S-Video and Composite  
Video input-equipped displays only.  
1 Press the Power/Menu button until the Power ON indicator blinks.  
After a moment, a No Signal Coming message appears.  
2 Wait for the No Signal Coming message to disappear, approximately  
3 to 5 seconds.  
3 Press the Power/Menu button to display the VGA VIDEO menu.  
4 Press the PLUS or MINUS (  
/
) control to enter video mode.  
5 Press the UP ( ) arrow to change video modes if you are using  
an alternate video source.  
6 Press the PLUS or MINUS (  
/
) control to select the desired  
video mode.  
Connecting the Optional Touch Screen  
If your VitalScreen CSR or VitalScreen CR display has the optional touch  
screen, connect the display 9-pin D-sub serial port to the computer 9-pin  
RS-232 serial port using the cable supplied with the touchscreen package.  
Next, connect the RS-232 cable to the 9-pin serial port on the back panel  
of the display.  
Do not operate the touch screen with sharp objects, such as a scalpel.  
Sharp objects can scratch or damage the touch screen. A damaged touch  
screen may pose a safety hazard.  
Mounting the Display  
When mounting your display, such as to a wall bracket or an  
articulated swing arm, make sure the maximum length of the  
screws inserted into the display mounts is 9 millimeters. Forcing  
the screws deeper into the mounts and exceeding this maximum  
length may damage the display.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
10 | Installing the Display  
Power Management System  
The VitalScreen CSR and VitalScreen CR displays comply with the  
VESA Display Power Management Signaling (DPMS) standard. This  
standard provides four power-saving modes, based on the display  
detecting the horizontal or vertical sync signals. This table describes  
the four modes.  
Mode  
On  
AC Input Power1  
60 watts maximum  
5 watts maximum  
5 watts maximum  
5 watts maximum  
LED Status  
Steady green  
Blinking green  
Blinking green  
Off  
Standby  
Suspend  
Off  
1
Including AC adapter  
When the display is in power-saving mode or detects incorrect timing,  
the screen is blank and the power LED indicator blinks.  
Landscape-to-Portrait Mechanical Conversion  
The 17.4" display (deskstand version) has a unique feature that allows  
a mechanical conversion of the display from the traditional landscape  
mode to a vertical portrait mode.  
Use both hands whenever you are changing the orientation of  
the display.  
1 Gently pull the lower half of the display toward you.  
You must tilt the display upward before rotating it.  
2 Rotate the display 90 degrees to left (counterclockwise) until it stops  
in portrait mode.  
3 Select, if necessary and/or available, the different option on the video  
card, or display settings on the control panel.  
4 Refer to www.portrait.com for software that allows conversion from  
landscape to portrait mode.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
The Display Controls  
Read this chapter carefully to use your VitalScreen CSR or  
VitalScreen CR display efficiently and effectively.  
Using the Onscreen Display  
The onscreen display (OSD) makes adjusting the display settings  
quick and easy. Use the OSD to adjust the brightness, contrast, volume,  
position, and language for the options in the display. You can access the  
OSD whenever both the computer and display are on. If the computer is  
off or in power-saving mode, the OSD is inaccessible.  
Onscreen Display Main Menu  
Call up the OSD Main Menu by momentarily pressing the Power/Menu  
button. Use the Function buttons (UP and DOWN arrows) to scroll  
through the menu items. When the desired submenu displays, use  
either Adjustment button (PLUS or MINUS control) to select the  
submenu. Then use the Function buttons to select the desired  
function and the Adjustment buttons to make the needed changes.  
The available control functions are grouped into categories. The  
selected mode of operation (either analog or digital) determines  
the available categories.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
11  
 
12 | Installing the Display  
Main menu  
The following table describes the main menus of the onscreen display.  
The Main Menus  
Basic setting  
Position  
Change brightness, contrast  
Change the display attributes  
Auto-adjust  
Auto-adjust the display parameters to optimum  
values (not available for digital mode)  
Color temperature  
Miscellaneous  
Adjust the color settings  
Audio volume, OSD H-position, OSD V-position,  
display mode, FW (firmware) version  
Video  
Switch to video input port. (Available with  
S-Video and Composite Video display)  
Language  
Support six different languages: English, Dutch,  
German, French, Spanish, Italian  
Input port  
Reset  
Exit  
Port 1 analog, Port 2 digital  
Reset display  
Close the onscreen display  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
Installing the Display | 13  
Function menus  
The following tables describe the function menus of the onscreen display.  
Basic Setting (Available in analog and/or digital mode)  
Contrast  
Adjust the contrast level of the display  
Analog  
Digital  
Brightness  
Adjust the brightness of the display’s  
backlight  
Analog  
Digital  
Video level  
Gamma  
Auto adjusts video level when selected  
Analog  
Analog  
Gamma curve adjustment, ranging from  
0.85 to 1.15  
Frame  
Sets border color when native size is  
selected and selected resolution is  
less than default (1280 x 1024)  
Analog  
To main menu  
Exit  
Position Menu (Analog mode only)  
Clock  
Adjust the display pixel alignment  
Phase  
Adjust the screen display for focus and clarity  
Appears at display resolution  
Default size  
Native size  
H-position  
V-position  
H-size  
Displays at computer resolution  
Horizontal position adjustment (not available for digital mode)  
Vertical position adjustment (not available for digital mode)  
Horizontal size adjustment  
V-size  
Vertical size adjustment  
Graphic/Text  
Select either Graph or Text expansion method (Only  
available in 720 x 400 and 640 x 480 resolutions)  
To main menu  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
14 | Installing the Display  
Color Temperature (Analog mode only)1  
Color 9300  
Color 6500  
Color user  
Set the color temperature of white to  
9300 degrees Kelvin  
Set the color temperature of white to  
6500 degrees Kelvin  
Enable "User Color" selection, and  
adjust individual RGB levels  
R
Adjust red contrast  
Adjust green contrast  
Adjust blue contrast  
G
B
To main menu  
1
Three sets of color temperature settings are available: two for standard  
settings and one for user adjustment.  
Miscellaneous Menu  
Audio volume  
OSD H-position  
OSD V-position  
Display mode  
F/W version  
To main menu  
Exit  
Audio volume adjustment  
Adjust the OSD position horizontally  
Adjust the OSD position vertically  
Shows the display mode  
Shows the firmware version  
Quick adjustment functions: Analog and digital modes  
For this function…  
Contrast  
Push this key…  
Function UP (  
Function DOWN (  
)
Brightness  
)
Audio volume  
Port selection  
Adjust PLUS (  
)
Adjust MINUS (  
)
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
Installing the Display | 15  
S-Video and Composite Video Settings  
These functions are active on the VitalScreen onscreen display when  
the display is in S-Video or Composite Video mode.  
This option is available only on the VitalScreen 17.4" CSR display.  
Settings  
The settings are selected with the Function buttons. Select the UP ( ) or  
DOWN ( ) arrow.  
Change the settings with the Adjustment buttons. Select the PLUS ( ) or  
MINUS ( ) control.  
Contrast  
Brightness  
Volume  
Input  
Adjust the contrast level of the display  
Adjust the brightness of the display’s backlight  
Adjust audio volume  
Switch between S-Video and Composite Video modes  
Switch between video and VGA/DVI inputs  
Adjust the hue level of the display  
Video VGA  
Hue  
Sampling  
Overscan  
Reset  
Change Sampling mode settings  
Turn Overscan ON or OFF  
Reset display S-Video or Composite Video settings  
Quick adjustment functions  
For this function… Push this key…  
Input  
Adjust MINUS ( ) twice  
Audio volume  
Video VGA  
Adjust PLUS (  
)
Power/Menu key,1 then push Adjust PLUS ( ) or  
Adjust MINUS (  
)
1
Pressing and holding the Power/Menu button for more than 2 seconds turns off  
the display.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
16 | Installing the Display  
Onscreen Display Lockout  
Both displays incorporate an OSD lockout function that you toggle  
active or inactive. Pressing three controls — Function DOWN ( ),  
Adjust PLUS ( ), and Adjust MINUS ( ) — simultaneously locks out  
the OSD from being enabled by the power control. Attempts to enable  
the OSD result in an OSD locked” message only. To unlock the OSD,  
press the same three controls in the same manner.  
Supported CVBS and S-Video Modes  
Supported video formats on VitalScreen displays with S-Video and  
Composite Video functionality include the following:  
PAL B, G, H, I, D  
NTSC M, Japan  
This option is available only on the VitalScreen 17.4" CSR display.  
In the table on page 17, A signifies analog mode and D signifies digital  
mode. Also, if the input timing is close to one of the modes, generally  
it can be displayed by manually adjusting the clock and/or phase from  
within the OSD menu.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
Installing the Display | 17  
Supported Video Modes  
Vertical  
Scanning  
Frequency  
(Hz)  
Horizontal  
Scanning  
Frequency  
(kHz)  
Sync  
Polarity or  
Composite  
Sync (H/V)  
Dot Clock  
(MHz)  
Operating  
Mode  
Item Standard  
Resolution  
1
2
3
4
5
6
7
8
9
NEC PC98  
640x400  
640X400  
640x480  
25.20  
21.05  
30.24  
57.28  
80.00  
25.18  
31.50  
25.18  
31.50  
25.18  
31.50  
31.50  
36.00  
36.00  
40.00  
50.00  
49.50  
56.25  
28.32  
35.50  
46.76  
65.00  
75.00  
78.75  
71.64  
94.50  
108.00  
121.50  
108.00  
108.00  
127.00  
135.00  
64.13  
74.25  
84.38  
81.00  
94.50  
94.50  
108.00  
117.00  
135.00  
70.15  
56.42  
66.67  
74.55  
75.02  
70.09  
85.08  
70.09  
85.08  
59.94  
72.81  
75.00  
85.01  
56.25  
60.32  
72.19  
75.00  
85.06  
70.09  
85.04  
60.00  
60.00  
70.07  
75.03  
66.13  
85.00  
75.00  
85.00  
60.00  
60.02  
69.85  
75.03  
59.98  
70.04  
77.07  
72.87  
85.53  
66.00  
76.64  
67.19  
76.10  
31.50  
24.83  
35.00  
49.73  
60.24  
31.47  
37.86  
31.47  
37.86  
31.47  
37.86  
37.50  
43.27  
35.16  
37.88  
48.08  
46.88  
53.67  
31.47  
37.93  
34.38  
48.36  
56.48  
60.02  
53.96  
68.68  
67.50  
77.09  
60.00  
63.98  
74.88  
79.98  
48.29  
56.59  
62.04  
60.99  
71.59  
61.84  
71.81  
71.69  
81.13  
-/-  
-/-  
A/D  
A
NEC PC98  
MAC 13" mode  
MAC 16" mode  
MAC 17" mode  
-/-  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A/D  
A
832x624  
-/-  
1024x768  
640x350  
-/-  
VGA  
+/-  
VESA  
VGA  
640x350  
+/-  
640x400  
-/+  
VESA  
640x400  
-/+  
10 VGA  
11 VESA  
12 VESA  
13 VESA  
14 VESA  
15 SVGA  
16 VESA  
17 VESA  
18 VESA  
19 VGA  
20 VESA  
21 MEDICAL  
22 XGA  
23 VESA  
24 VESA  
25  
640x480  
-/-  
640x480  
-/-  
640x480  
-/-  
640x480  
-/-  
800x600  
+/+  
+/+  
+/+  
+/+  
+/+  
-/+  
800x600  
800x600  
800x600  
800x600  
720x400  
720x400  
-/+  
1024x512  
1024x768  
1024x768  
1024x768  
1024x768  
1024x768  
1152x864  
1152x864  
1280x960  
1280x1024  
1280x1024  
1280x1024  
1024x768  
1024x768  
1024x768  
1024x800  
1024x800  
1152x900  
1152x900  
1280x1024  
1280x1024  
-/-  
-/-  
-/-  
+/+  
+/+  
+/+  
+/+  
+/+  
+/+  
+/+  
+/+  
+/+  
H+V  
H+V  
H+V  
H+V  
H+V  
H+V  
H+V  
H+V  
H+V  
26 VESA  
27 VESA  
28 VESA  
29 VESA  
30 VESA  
31 VESA  
32 VESA  
33 SUN  
34 SUN  
35 SUN  
36 SUN  
37 SUN  
38 SUN  
39 SUN  
40 SUN  
41 SUN  
A
A
A
A
A
A
A
A
A
A
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
 
Technical Information  
VitalScreen 17.4" CSR/CR  
Display panel  
Specification  
17.4-inch (442-mm) SXGA active matrix LCD  
Full color supporting 8-bits/color  
Display colors  
Dimensions (W x H x D)  
Landscape mode 18" x 18" x 8.5" (457 mm x 457 mm x 216 mm)  
Portrait mode 15" x 19.5" x 8.5" (381 mm x 495 mm x 216 mm)  
Weight  
20 lb (9 kg)  
Display area (W x H)  
Response time  
Viewing angle  
Contrast ratio  
Brightness  
13.6" x 10.9" (345.6 mm x 276.48 mm)  
25 milliseconds Wht>Blk @ 25 milliseconds max.  
160 degrees (horizontal or vertical)  
400:1 in dark room (0 lux) typical  
Non-touch 200 cd/m2 typical  
Resistive touch 176 cd/m2 typical  
Pixel pitch (W x H)  
Reliability  
0.297 mm x 0.297 mm  
Monitor 30,000 hours mean time between failure (MTBF)  
Backlight 50,000 hours to reach 50% of initial brightness  
Scanning frequency  
Power consumption  
Analog Horizontal  
Vertical  
Digital Horizontal  
Vertical  
24 to 81 kHz  
56 to 85 Hz  
38.6 to 60 kHz  
50 to 75 Hz  
60 watts maximum  
<5 watts in standby or off mode  
Power supply  
Audio  
12 volts / 5 amps, 60 watts  
Stereo speakers with integral amp.  
(min. 1W/channel, <1% distortion)  
Temperature  
Humidity  
Operating 0 to 40 degrees Celsius  
Nonoperating -20 to 60 degrees Celsius  
Operating 10 to 90 percent relative humidity (noncondensing)  
Nonoperating 10 to 90 percent relative humidity (noncondensing)  
Altitude  
Operating 0 to 8000 ft (2400 m)  
Nonoperating 0 to 40,000 ft (12,200 m)  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
19  
 
Troubleshooting  
PROBLEM: Display is unclear and unstable  
This procedure is for users of analog VGA.  
This LCD device comes pre-adjusted with standard VGA timing. Due to  
output differences among various VGA cards, you may initially experience  
an unclear and unstable display when a new display mode or new VGA  
card is detected. To correct the problem, follow these steps:  
1 Apply the Auto-Adjust option in the OSD menu for the display to  
adjust automatically to the video signal.  
2 If the picture remains unstable, consider manual adjustment of the  
clock and phase (in the OSD menu of the display). These adjustments  
are not recommended for nontechnical users.  
3 If the system still does not function properly, get help from technical  
support at your system provider.  
PROBLEM: No image appears on LCD screen  
If no image appears on the LCD screen, follow these steps:  
1 Make sure the power indicator on the display is illuminated, all  
connections are secure, and the system is running on a supported  
video timing mode.  
2 If the power LED is not illuminated, make sure the AC power  
connector is securely connected. If the AC adapter has an LED,  
verify that the LED is illuminated. If it is not, contact your dealer  
for assistance.  
3 Turn the display off and then turn it back on.  
4 Connect your system to another Planar 17.4 display, if one is available.  
If the system functions properly with the alternate display but not  
with the original display, and the original displays power LED is  
blinking, the output timing of the computers video board may be out  
of the displays synchronous range. Change to an alternate mode  
(1280 x 1024, or less), or connect to an alternate video source and  
repeat steps 1 and 2.  
5 Ensure that the computers video port is enabled (DVI or VGA).  
This is a function of the video board in the user computer system.  
See your systems video board documentation for instructions on  
how to enable the video port.  
6 If the system does not function with either display, get help from  
technical support at your system provider.  
20  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
21  
Index  
A
M
adjustment functions, quick, 14, 15  
assistance, technical, 24  
main menu, onscreen display, 11, 12  
mechanical conversion, landscape to  
portrait, 10  
menu  
function, 13  
main, 11, 12  
B
back panel, 6  
cleaning instructions, xi  
components, identifying, 4  
connecting  
AC power to display, 7  
display to system, 8  
optional touch screen, 9  
video device, 9  
controls, display, 11  
conversion, mechanical, 10  
customer support, 24  
CVBS and S-video modes, 16  
O
onscreen display  
function menu, 13  
lockout, 16  
main menu, 11, 12  
using, 11  
optional touch screen, connecting, 9  
ordering information, 25  
P
power management system, 10  
product symbols, xii  
D
display  
Q
components, 4  
quick adjustment functions, 14, 15  
connecting AC power, 7  
connecting to system, 8  
controls, 11  
R
repair service, 23, 24  
S
installing, 7  
safety instructions, x  
selecting workspace, 3  
service, repair, 23, 24  
screen, LCD, 4  
specifications, display, 19  
supported video modes, 16  
symbol explanations, xii  
onscreen lockout, 16  
onscreen main menu, 11, 12  
description of, 1, 2  
specifications, 19  
troubleshooting, 20  
unpacking, 3  
using onscreen, 11  
disposal information, xi  
T
technical  
F
assistance, 24  
front panel, 5  
information, 19  
function menu, 13  
touch screen (optional), connecting, 9  
troubleshooting, 20  
functions, quick adjustment, 14, 15  
I
U
information  
disposal, xi  
ordering, 25  
technical, 19  
installing display, 7  
instructions  
cleaning, xi  
safety, x  
unpacking display, 3  
using onscreen display, 11  
V
video  
device, connecting, 9  
modes, supported, 16  
settings, S-video and composite, 15  
L
W
landscape-to-portrait conversion, 10  
LCD screen, 4  
lockout, onscreen display, 16  
warranty, 23  
workspace, selecting, 3  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
 
23  
Description of Warranty  
Planar Systems, Inc. (Planar) warrants that the goods sold hereunder  
will be free of defects in materials and workmanship, and such goods  
will substantially conform to the specifications furnished by Planar,  
and to any drawings or specifications furnished to Planar by the Buyer  
if approved by Planar. This warranty shall be effective only if Planar  
receives notice of such defect or nonconformance during the period of  
the warranty. Planars sole and exclusive liability for breach of warranty  
shall be, at the companys option, to repair or replace the Planar  
product(s) with refurbished units or provide a credit to Buyer in  
the amount of the purchase price.  
Commencement and duration of warranty  
The warranty period begins on the date of shipment from Planar.  
The goods sold hereunder are warranted for a period of 36 months  
from date of shipment unless otherwise agreed to by Buyer and  
Planar. No extension of the warranty will be given during the time  
the goods are in the possession of Planar.  
Place of repair or replacement  
To obtain service under this warranty, Buyer must notify Planar of the  
defect before expiration of the warranty period and request a Return  
Material Authorization Number (RMA).” If the configuration has been  
modified in any manner, the product must be returned to its original  
configuration before any warranty service will be performed by Planar.  
No goods are to be returned to Planar without prior authorization.  
Buyer will be responsible for packaging and shipping the defective  
goods to the appropriate Planar service facility. For North America,  
the service facility is located in Beaverton, Oregon; for Europe, the  
service facility is located in Espoo, Finland.  
Limitation of warranty  
The foregoing warranty shall not apply to defects resulting from  
(a) improper or inadequate maintenance by Buyer; (b) unauthorized  
modification of the goods; (c) operations of the goods outside the  
environmental specifications of the goods; (d) neglect, misuse, or  
abuse of the goods; or (e) modification or integration with other  
goods not covered by the Planar warranty when such modification  
or integration increases the likelihood of damage to the goods.  
THE WARRANTY IS GIVEN BY Planar IN LIEU OF ANY OTHER  
WARRANTIES, EXPRESSED OR IMPLIED. Planar DISCLAIMS ANY  
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS  
FOR A PARTICULAR PURPOSE. Planars RESPONSIBILITY TO  
REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE  
AND EXCLUSIVE REMEDY PROVIDED TO THE BUYER FOR  
BREACH OF THIS WARRANTY. Planar WILL NOT BE LIABLE  
FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL  
DAMAGES IRRESPECTIVE OF WHETHER Planar HAS ADVANCE  
NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
24  
The warranty set forth above shall not be enlarged, diminished, or  
affected by, and no obligation or liability shall arise from, Planar, any  
authorized dealer, or any other persons rendering of technical advice,  
assistance, or services in connection with the Buyers order of the goods  
furnished hereunder. The Buyer is not relying on skill or judgment of  
Planar to select or furnish suitable goods.  
Installation  
Planar makes no warranty with respect to any installation of Planar  
product(s) by Planar, any authorized dealer, or any other person.  
Technical assistance  
In North America, call (503) 748-1100 between 8 A.M. and 5 P.M. Pacific  
time, Monday through Friday, or send a description of your technical  
issues and e-mail address to tech_support@planar.com.  
In Europe, call +358 9 420 01 between 8 A.M. and 4 P.M. Finnish  
time (Eastern European time), Monday through Friday, or send  
a description of your technical issues and e-mail address to  
intltech_support@planar.com.  
Repair service  
In North America, call Planar at (503) 748-1100 between 8 A.M. and  
4 P.M. Pacific time, Monday through Friday, or fax your request to  
(503) 748-1493. You will need the units serial number and a brief  
description of the problem to receive an RMA number.  
In Europe, call Planar Customer Service at +358 9 420 01 between 8 A.M.  
and 4 P.M. Eastern European time, Monday through Friday, or fax your  
request to +358 9 420 0200. You will need the units serial number and  
a brief description of the problem to receive an RMA number.  
To protect Planar employees from potential health hazards, Planar  
requires that the RMA product be disinfected before returning to  
Planar for service. Any product not cleaned prior to shipment will  
be returned to the customer.  
Returns are not accepted without an assigned RMA number.  
In-transit damage is not covered by the warranty. Insure your shipment.  
Planar will only pay for the return shipment by surface transportation.  
It is the responsibility of the sender to prepay transportation charges.  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
25  
Ordering Information  
VitalScreen CSR  
Part Number  
VS17.4SXAD 17.4-inch SXGA VitalScreen Medically Certified  
996-0497-00  
Display (non-touch) with desk stand and U.S. power cord  
VS17.4SXAD 17.4-inch SXGA VitalScreen Medically  
Certified Display (non-touch) with desk stand and  
European power cord  
996-0497-01  
996-0497-02  
996-0497-03  
996-0498-00  
996-0498-01  
996-0498-02  
996-0498-03  
996-0533-00  
996-0533-01  
996-0533-02  
996-0533-03  
996-0534-00  
996-0534-01  
996-0534-02  
996-0534-03  
VS17.4SXAD 17.4-inch SXGA VitalScreen Medically  
Certified Display (non-touch) with standard mounting  
(VESA compatible, 75 mm) and U.S. power cord  
VS17.4SXAD 17.4-inch SXGA VitalScreen Medically  
Certified Display (non-touch) with standard mounting  
(VESA compatible, 75 mm) and European power cord  
VS17.4SXAD-TR 17.4-inch SXGA VitalScreen Medically  
Certified Display (resistive touch) with desk stand and  
U.S. power cord  
VS17.4SXAD-TR 17.4-inch SXGA VitalScreen Medically  
Certified Display (resistive touch) with desk stand and  
European power cord  
VS17.4SXAD-TR 17.4-inch SXGA VitalScreen Medically  
Certified Display (resistive touch) with standard mounting  
(VESA compatible, 75 mm) and U.S. power cord  
VS17.4SXAD-TR 17.4-inch SXGA VitalScreen Medically  
Certified Display (resistive touch) with standard mounting  
(VESA compatible, 75 mm) and European power cord  
VS17.4SXADV SXGA 17.4-inch video-equipped VitalScreen  
Medically Certified Display with desk stand and U.S. power  
cord (non-touch)  
VS17.4SXADV SXGA 17.4-inch video-equipped VitalScreen  
Medically Certified Display with desk stand and European  
power cord (non-touch)  
VS17.4SXADV SXGA 17.4-inch video-equipped VitalScreen  
Medically Certified Display with universal VESA mounting  
solution and U.S. power cord (non-touch)  
VS17.4SXADV SXGA 17.4-inch video-equipped VitalScreen  
Medically Certified Display with universal VESA mounting  
solution and European power cord (non-touch)  
VS17.4SXADVTR SXGA 17.4-inch video-equipped  
VitalScreen Medically Certified Display with desk stand and  
U.S. power cord (resistive touch)  
VS17.4SXADVTR SXGA 17.4-inch video-equipped  
VitalScreen Medically Certified Display with desk stand and  
European power cord (resistive touch)  
VS17.4SXADVTR SXGA 17.4-inch video-equipped  
VitalScreen Medically Certified Display with universal VESA  
mounting solution and U.S. power cord (resistive touch)  
VS17.4SXADVTR SXGA 17.4-inch video-equipped  
VitalScreen Medically Certified Display with universal VESA  
mounting solution and European power cord (resistive touch)  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
26  
VitalScreen CR  
Part Number  
CM17.4SXAD 17.4 SXGA VitalScreen CR (non-touch) with  
desk stand and U.S. power cord  
996-0514-00  
CM17.4SXAD 17.4 SXGA VitalScreen CR (non-touch) with  
desk stand and European power cord  
996-0514-01  
996-0514-02  
CM17.4SXAD-TR 17.4 SXGA VitalScreen CR (non-touch)  
with standard mounting (VESA compatible, 75 mm) and  
U.S. power cord  
CM17.4SXAD-TR 17.4 SXGA VitalScreen CR (non-touch)  
with standard mounting (VESA compatible, 75 mm) and  
European power cord  
996-0514-03  
CM17.4SXAD-TR 17.4 SXGA VitalScreen CR (resistive  
touch) with desk stand and U.S. power cord  
996-0515-00  
996-0515-01  
996-0515-02  
CM17.4SXAD-TR 17.4 SXGA VitalScreen CR (resistive  
touch) with desk stand and European power cord  
CM17.4SXAD-TR 17.4 SXGA VitalScreen CR (resistive  
touch) with standard mounting (VESA compatible, 75 mm)  
and U.S. power cord  
CM17.4SXAD-TR 17.4 SXGA VitalScreen CR (resistive  
touch) with standard mounting (VESA compatible, 75 mm)  
and European power cord  
996-0515-03  
Items Included with All Display Products  
Part Number  
Cable, VGA-VGA, 2 m, white, smooth surface (analog)  
with audio  
903-0293-00  
Cable, DVI-DVI, 2 m, white, smooth surface with audio  
903-0292-00  
020-0168-00  
17.4" VitalScreen CSR and VitalScreen CR  
operations manuals (English)  
3 m S-Video/CVBS cable (VS17.4SXADV only)  
3 m audio cable (VS17.4SXADV only)  
Available Cables and Accessories  
100-mm VESA mounting plate  
903-0308-00  
903-0310-00  
Part Number  
501-0415-00  
903-0251-00  
903-0169-00  
903-0233-00  
902-0238-00  
501-0380-00  
European medical grade power cord, 1.5 m  
U.S. medical grade power cord, 3 m  
Touchscreen cable, 2 m, white, smooth surface  
12 V medical grade power supply  
Planar desk stand for 17.4" display  
VS17.4SXAD / CM17.4SXAD (020-0168-00B)  
 
 
North and South America Sales  
Europe and Asia-Pacific Sales  
Planar Systems, Inc.  
Planar Systems, Inc.  
1195 NW Compton Drive  
Beaverton, OR 97006-1992  
+1 (503) 748-1100 phone  
+1 (503) 748-1493 fax  
Olarinluoma 9, P.O. Box 46  
FIN-02201 Espoo, Finland  
+358 9 420 01 phone  
+358 9 420 0200 fax  
 

Perle Systems Switch 5500305 20 User Manual
Philips Car Satellite TV System 42PFL7603D User Manual
Philips MP3 Docking Station DPC850 User Manual
Philips Stereo Amplifier SDW5005O User Manual
Pioneer CD Player PD M455 User Manual
Planar Computer Monitor PL2011 User Manual
Polycom Home Theater Server RMX 1800 User Manual
Poulan Trimmer 952711930 User Manual
PYLE Audio MP3 Docking Station PIP30 User Manual
PYLE Audio MP3 Docking Station PMNP2B User Manual